The Schleiferl V1.2, in a new design and further developed, is the sharpening tool of the future, which eliminates the disadvantages of previous sharpening tools. It has the following advantages due to the grinding belt as a sharpening principle: – high removal rate – Perfectly shaped tooth profiles (front and roof angle), easily achievable – no annealing of the teeth – The chrome layer of the saw teeth is not damaged – no loss of shape of the sharpening tool due to wear – Chain is sharpened on the bar – Tolerant of angle errors when sharpening due to the grinding belt running out at the top – Suitable for very small chains (1/4″ Picco) as well as for harvester chains (.404) (additional grinding shafts required) – economical & quickly The Schleiferl is the first chain sharpening tool that works with a grinding belt. This is driven by small hex screwdrivers. The speed of the screwdriver should be at least 3000 rpm. Practical tip for abrasive belt life: High speed + low contact pressure = long abrasive belt life. Abrasive grains can wear down in the micrometer range, but they need sufficient time to be able to process the steel. Excessive grinding pressure leads to the entire grain tearing off the grinding belt. High belt speed and low contact pressure give the abrasive grain time to process the saw tooth. Scope of delivery standard: Grinder incl. high-quality transport bag Hex screwdriver according to selection 1 spare sanding belt Grinding shaft 0.325 chain pitch Grinding shaft 3/8″ chain pitch Scope of delivery in the set: grinder 1 spare sanding belt Grinding shaft 0.325 chain pitch Grinding shaft 3/8″ chain pitch

The ValFix is the newest, lightest, cheapest spindle wedge on the market and another real BaSt-Ing innovation. With a dead weight of less than 1.4kg and a lifting force of over 15t, it generates more than 1000g (!) Lifting force per 1g of dead weight. A secret of the ValFix is that it works with a very flat wedge angle. Due to this small angle, it can be constructed particularly easily and still generate high lifting forces. In order to still achieve practical lifting heights despite the small wedge angle, it has a completely new spindle construction. The ValFix spindle is partially integrated. This means that half of the spindle is protected in the felling wedge and only the second half of the spindle is exposed. A sufficient wedge stroke can thus be achieved with a long spindle travel. Grease nipples on both threaded nuts ensure easy maintenance and sufficient lubrication even on long working days. The advantages of the ValFix at a glance: very short No axial bearing required due to the principle low weight of 1.4kg easy relubrication using a grease nipple (no grease spray required) no weld seam in the spindle low wear The ValFix may be operated with a maximum 700 Nm impact wrench. Tip: With the right choice of impact wrench, it can also be used for the grinder as well as for the depth gauge grinder. e.g. Bosch GDX 18V-200.

ValFast – In a new design! The robust spindle wedge with which the strenuous and time-consuming wedging of trees is a thing of the past. Designed so that you can leave the ax or sledgehammer at home. Optimized for use with an impact wrench, but it can also be operated with a ratchet at any time.In the current version we have further developed ValFast in some details. An example is the drive spindle. From 2022, it will be machined from high-quality CrMo steel and will therefore permanently withstand even the strongest impact wrench. Furthermore, the bearing and design of the chisel tip has been revised. The ValFast is therefore a sophisticated felling wedge for daily use in professional wood harvesting. Suitable impact wrench types: Maktia DTW1002 & DTW1001 Makita TW001G Milwaukee ONFHIWF12 and ONEFHIWF34 Bosch GDS18V-1050H DeWalt DCF899 Accessories shown in the pictures are not part of the scope of delivery.

Product novelty 2020 SpaltFast is the first 1 meter plywood splitter that is mass-produced and another real BaSt-Ing innovation. The advantages of the SpaltFast summarized: floating knife arrangement for a small amount of spreader wood High hourly output, no manual operator intervention required No adjustment to the trunk diameter required: small and large trunk diameters can be split flexibly easy operation and control from the timber trailer automated return for smooth handling Passage of the plywood splitter: 90cm 150kg toothbrush for quick and easy removal of jammed wood from the splitting knives Control buttons are attached to the crane joysticks and connected to the log splitter with a plug Technical specifications: 25t pressure force Own oil supply with powerful 112ccm cast pump, oil cooler and 60l oil tank Hydraulic system dimensioned for 100l/min Dead weight approx. 2.5t Made of high quality steel S355 automatic change of direction of the cylinder by means of realis control Tires: 15.0 / 55 - 17 ALLIANCE Width: 250cm Length: 415cm Height: 160cm Made in Germany FAQ: Is the SpaltFast also available with a log lifter?: No, the SpaltFast is designed for crane loading only. The crane is also required to lift the toothbrush into the canal or to quickly turn pieces of wood in the canal. Manual loading for the SpaltFast is not possible or not permitted for safety reasons. What hourly output does the SpaltFast have?: This is heavily dependent on the qualification of the crane operator and the quality of the wood. 10th / h are no problem with good conditions. However, you have to have the log storage and the procurement of the logs under control. What happens with knotty wood?: In general, with every log splitter, the poorer the quality is that you split, the "worse" the meter wood will be. Thanks to the floating storage, we can stay in the grain much better and thus achieve better wood quality than with a fixed knife or a fixed star. However, the more knotty the pieces of wood, the more often the splitting knife unit has to be cleaned. We recommend using very knotty material for the chopper. With the SpaltFast, however, e.g. The knot-free area is split off from large logs and the rest can be chopped up. How much spreader wood is created?: Depending on the quality of the wood, more or less spreader is created. We have tried to generate little spreader, but more is created than with a classic splitter. From a business point of view, we are convinced that the additional wood will be compensated by the time advantage, especially since the wood is still suitable for chopping or kindling. Why can't the SpaltFast be placed on the logging trailer?: The weight of 2.5t exceeds the lifting capacity of most logging trailer cranes, and the view of the splitting duct is extremely limited, which makes the work considerably more difficult. Last but not least, it is complex to provide the high oil capacity of 100l in the stanchion cage. What power requirement does the SpaltFast have?: The SpaltFast can be used from 30HP. With knotty material or at full working speed, we recommend 50 HP tractor power. Where is the SpaltFast produced?: The SpaltFast is prepared in southern Germany by companies specializing in your field (flame cutting, painting, welding) and then assembled by us. Scope of delivery: Log splitter "SpaltFast" including general operating permit "Toothbrush" Control operating manual without cardan shaft   Start of production after 40% down payment, delivery after final payment. Delivery time: approx. 3 months Shipping costs are to be borne by the buyer. Note: We are continuously developing our products. The product delivered may differ from the illustration. Subject to change.

The “Schleiferl – light” with a new design, new material and further developed in detail. Due to the low dead weight and the improved feel, sharpening chainsaws is even more fun. The special grinding belt ensures maximum sharpness with a long service life. The grinder sharpens the chainsaw with a grinding belt. The fine grinding belt achieves a unique sharpness on the chain. Chains can be quickly sharpened using the bit screwdriver drive. The grinder works with both the small chains for cordless saws (1/4″P) and the large harvester chains (.404″). The advantages at a glance: – Perfectly shaped tooth cutting edges thanks to the grinding belt that runs out at the top – simple application – no loss of shape of the sharpening tool due to wear – Fast sharpening without having to remove the chains from the bar – Tolerant to angle errors when sharpening due to the grinding belt running out at the top – Suitable for very small chains (1/4″ Picco) as well as for harvester chains (.404) – economical & fast – Long service life of the sanding belts – economical & fast   Practical tip for the service life of the grinding belt: High speed + low contact pressure = long service life for the grinding belt. Abrasive grains can wear down in the micrometer range, but they need sufficient time to be able to process the steel. If the grinding pressure is too high, the entire grain tears off the grinding belt. High belt speed and low contact pressure give the abrasive grain time to process the saw tooth. Scope of delivery: Grinder incl | Premium abrasive belt and abrasive shaft Hex screwdriver according to selection Options: carry bag grinding shafts Endurance – sanding belt